;
; (C)Copyright Distributed Processing Technology, 1989-1996
;    All Rights Reserved.
;
; DPT EISA to SCSI Host Bus Adapter w/ Optional Cache
;                   Configuration File
;
;    Date     = 5/9/96
;    Version  = (See version at end of this file.)
;    Filename = !DPTA410.CFG
;

BOARD
  ID          = "DPTA410"
  NAME        = "DPT EISA SCSI Host Bus Adapter"
  MFR         = "DPT"
  CATEGORY    = "MSD"
  SLOT        = EISA
  LENGTH      = 341
  SKIRT       = NO
  READID      = YES
  BUSMASTER   = 999
  AMPERAGE    = 2500
  IOCHECK     = INVALID
  DISABLE     = SUPPORTED
  COMMENTS    = "\nThis configuration file is for use with all Distributed
                Processing Technology SmartCache or SmartRAID EISA SCSI Host Bus Adapters\n
                which use a 128 byte NV-RAM and have a 16k BIOS chip.\n
                This includes the PM2042, PM2142 and PM3332, with or without floppy.\n\n
                Key features of the adapter are:\n
                \t* Up to 64MB of disk cache w/ ECC protection\n
                \t* ECC protection of data across SCSI bus\n
                \t* RAID-0, 1, and 5\n
                \t* 33MB/sec EISA burst transfer\n
                \t* SCSI-3 compliant\n
                \t* up to 20mHz SCSI sync transfer\n
                \t* Universal EATA driver support\n\n
                For additional information, contact:\n
                \tDPT Customer Support\n
                \t(407) 830-5522"


IOPORT(1)     = 0zC90h
IOPORT(2)     = 0zC84h
IOPORT(3)     = 0zC88h
  SIZE        = WORD
IOPORT(4)     = 0zC89h
IOPORT(5)     = 0zC8Ah
IOPORT(6)     = 0zC8Bh
IOPORT(7)     = 0zC8Ch
IOPORT(8)     = 0zC8Dh
IOPORT(9)     = 0zC8Eh
IOPORT(10)    = 0zC8Fh
IOPORT(11)    = 0zC94h

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

JUMPER(1)     = 1
  NAME        = "Floppy Enable"
  JTYPE       = PAIRED
  LABEL       = LOC(1) "Y20"
  FACTORY     = LOC(1) 1
  VERTICAL    = YES
  REVERSE     = NO
  COMMENTS    = "Install jumper to enable floppy controller on card."
  HELP        = "If these pins are not jumpered the onboard floppy controller
                 is disabled.  If you wish to enable it, jumper these pins."

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

GROUP         = "CONTROLLER PARAMETERS"
TYPE          = "MSD,DSKCTL"

FUNCTION      = "Interrupt Number"
  COMMENTS    = "Select Level to share interrupts."
  HELP        = "These interrupts may also be chosen
                 as Edge (non-sharable) or Level (sharable)."
  CHOICE      = "15 Level"
    FREE
    IRQ       = 15
    TRIGGER   = LEVEL
    SHARE     = "DPT"
    INIT      = IOPORT(1) LOC(5 4 3) 010
    INIT      = IOPORT(1) LOC(2) 1
  CHOICE      = "11 Level"
    FREE
    IRQ       = 11
    TRIGGER   = LEVEL
    SHARE     = "DPT"
    INIT      = IOPORT(1) LOC(5 4 3) 001
    INIT      = IOPORT(1) LOC(2) 1
  CHOICE      = "14 Level"
    FREE
    IRQ       = 14
    TRIGGER   = LEVEL
    SHARE     = "DPT"
    INIT      = IOPORT(1) LOC(5 4 3) 100
    INIT      = IOPORT(1) LOC(2) 1
  CHOICE      = "15 Edge"
    FREE
    IRQ       = 15
    TRIGGER   = EDGE
    INIT      = IOPORT(1) LOC(5 4 3) 010
    INIT      = IOPORT(1) LOC(2) 0
  CHOICE      = "11 Edge"
    FREE
    IRQ       = 11
    TRIGGER   = EDGE
    INIT      = IOPORT(1) LOC(5 4 3) 001
    INIT      = IOPORT(1) LOC(2) 0
  CHOICE      = "14 Edge"
    FREE
    IRQ       = 14
    TRIGGER   = EDGE
    INIT      = IOPORT(1) LOC(5 4 3) 100
    INIT      = IOPORT(1) LOC(2) 0

FUNCTION      = "Floppy Control"
COMMENTS      = "Select Enable to access via standard motherboard BIOS.\n
                Install jumper Y20 to enable."
  CONNECTION  = "Floppy Connector, J8 Top Middle"
  CHOICE      = "Enabled"
    FREE
    PORT      = 3F0h-3F7h
    INIT      = JUMPER(1) LOC(1) 1
    INIT      = IOPORT(1) LOC(0) 0
  CHOICE      = "Disabled"
    FREE
    INIT      = JUMPER(1) LOC(1) 0
    INIT      = IOPORT(1) LOC(0) 0

FUNCTION      = "SCSI BIOS ROM Address"
  COMMENTS    = "Select C8000 or D8000 (size 16KB) to allow the BIOS to see the
                 onboard ROM."
  HELP        = "This ROM is normally the SmartROM, an INT13
                 replacement BIOS, which allows for higher performance, larger
                 capacity, and easier installation."
  CHOICE      = "Enabled at C8000h"
    FREE
    INIT      = IOPORT(11) LOC(1) 1
    INIT      = IOPORT(11) LOC(2) 0
    INIT      = IOPORT(11) LOC(3) 1
    MEMORY    = 16K
    ADDRESS   = 0C8000h
    WRITABLE  = NO
    MEMTYPE   = OTH
    SIZE      = BYTE
    CACHE     = YES
  CHOICE      = "Disabled"
    FREE
    INIT      = IOPORT(11) LOC(1) 0
  CHOICE      = "Enabled at D8000h"
    FREE
    INIT      = IOPORT(11) LOC(1) 1
    INIT      = IOPORT(11) LOC(2) 1
    INIT      = IOPORT(11) LOC(3) 1
    MEMORY    = 16K
    ADDRESS   = 0D8000h
    WRITABLE  = NO
    MEMTYPE   = OTH
    SIZE      = BYTE
    CACHE     = YES

ENDGROUP

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

FUNCTION      = "!DPTA410.CFG Version"
   CHOICE     = "6EC"
   FREE

; MUST clear config regs not used above
   INIT       = IOPORT(5) LOC(7-0) 00000000
   INIT       = IOPORT(6) LOC(7-0) 00000000

; THIS STATEMENT ENABLES TIMEOUTS

   INIT       = IOPORT(8) LOC(2) 0

; FLOPPY MUST ALWAYS BE AT PRIMARY, ENSURING 3F6

   INIT       = IOPORT(1) LOC(0) 0

; THIS STATEMENT ENABLES BUS MASTERING

   INIT       = IOPORT(2) LOC(0) 1

; THIS STATEMENT DISABLES ISA ADDRESSING mode

   INIT      = IOPORT(1) LOC(1) 1
   INIT      = IOPORT(1) LOC(6) 1

; THIS STATEMENT IS THE VERSION OF THE CONFIG FILE

   INIT       = IOPORT(4) LOC(2-0) 110

;  "Host Bus Adapter SCSI ID set to 7 by default"
   INIT       = IOPORT(4) LOC(5-3) 111

; SCSI termination BUS 0-2 enabled
   INIT       = IOPORT(9) LOC(0) 0
   INIT       = IOPORT(1) LOC(7) 0
   INIT       = IOPORT(9) LOC(1) 0
   INIT       = IOPORT(9) LOC(2) 0

; SCSI term pwr BUS 0-2 enabled
   INIT       = IOPORT(9) LOC(6-4) 000

; SCSI rate set to 10mhz
   INIT       = IOPORT(8) LOC(4-3) 00

; External CABLE detect is disabled
   INIT       = IOPORT(8) LOC(5) 1

; SCSI Command Queing enabled
   INIT       = IOPORT(8) LOC(0) 0

; Caching enabled for both reads/writes
   INIT       = IOPORT(7) LOC(7) 0
   INIT       = IOPORT(8) LOC(7) 0

; 80% Max dirty level
   INIT       = IOPORT(7) LOC(0) 1

; 30% Read Ahead level
   INIT       = IOPORT(7) LOC(1) 0

; Read ahead enbled
   INIT       = IOPORT(7) LOC(2) 0

; Long record caching disabled
   INIT       = IOPORT(7) LOC(3) 0

; Use store EISA parms stored on disk device if present
   INIT       = IOPORT(8) LOC(1) 0

; THIS STATEMENT ENABLES THE CONFIG ( F8 cmd reg write)

   INIT       = IOPORT(10) LOC(7-0) 11111000